IP Camera Bandwidth Calculator

Choose the camera resolution, codec, and frame rate, or enter your own bitrate. The calculator multiplies by the number of cameras and compares the total with the switch link you plan to use. Not sure which resolution to pick? See how many megapixels a security camera needs for your scene width.

Bitrate per camera–
Total for all cameras–
Share of the selected link–
Cameras per 100 Mb/s–
Cameras per 1 Gb/s–
Data per camera per day–

Presets are Hikvision’s recommended main-stream bitrates. Link speeds are nominal IEEE 802.3 line rates, and real throughput is lower once protocol overhead and other traffic are counted. Sub-streams, remote viewing, and recording to a separate NVR add their own traffic.

IP Camera Bandwidth per Camera Chart

A 4 MP camera on H.265 at 30 fps uses about 4.1 Mbps by Hikvision’s recommendation, against about 8.2 Mbps on H.264. A 2 MP camera on H.265 needs about 2.0 Mbps and a 4K camera about 8.2 Mbps.

H.265 recommended bitrate (Mbps)

Resolution30 fps25 fps20 fps15 fps10 fps
2 MP (1920 × 1080)2.052.051.541.020.77
4 MP (2560 × 1440)4.104.103.072.051.54
5 MP (2592 × 1944)4.614.613.462.301.73
8 MP / 4K (3840 × 2160)8.198.196.144.103.07

H.264 recommended bitrate (Mbps)

Resolution30 fps25 fps20 fps15 fps10 fps
2 MP (1920 × 1080)4.104.103.072.051.54
4 MP (2560 × 1440)8.198.196.144.103.07
5 MP (2592 × 1944)9.229.226.914.613.46
8 MP / 4K (3840 × 2160)16.3816.3812.298.196.14

Values are Hikvision’s recommended main-stream bitrates in Kbps, divided by 1,000 and rounded. Hikvision lists 4 MP as 2560 × 1440 and gives the same values for 2688 × 1520.

H.264 vs H.265 vs Smart Codecs at 30 fps

Hikvision’s H.264+ and H.265+ modes publish a target bitrate plus a higher maximum. The target is the typical average for a mostly static scene; plan for the maximum when the scene is busy.

Resolution (30 fps)H.264H.265H.264+ targetH.265+ target
2 MP (1920 × 1080)4.10 Mbps2.05 Mbps2.05 Mbps1.44 Mbps
4 MP (2560 × 1440)8.19 Mbps4.10 Mbps4.10 Mbps2.05 Mbps
5 MP (2592 × 1944)9.22 Mbps4.61 Mbps4.61 Mbps2.30 Mbps
8 MP / 4K (3840 × 2160)16.38 Mbps8.19 Mbps8.19 Mbps4.10 Mbps

How Much Does H.265 Really Save?

The headline figure is 50 percent. ITU said when it approved HEVC in January 2013 that the new codec needs only half the bit rate of H.264, and Hikvision’s tables apply exactly that halving. Axis reports a smaller real-world gain of 15 to 40 percent at comparable quality.

Axis test sceneH.264H.265Saving
Busy city23.56 Mbps16.84 Mbps29%
Traffic monitoring20.53 Mbps15.77 Mbps23%
Daytime city16.21 Mbps13.25 Mbps18%
Nighttime4.77 Mbps3.53 Mbps26%

Measured by Axis with simultaneous streams in its AV1 white paper. Savings are calculated from the published Mbit/s values.

What Changes Camera Bandwidth

  • Scene activity and lighting. Hanwha lists both as bitrate factors, and its highway profile uses twice the bandwidth of its retail profile. Hikvision suggests 20 to 30 percent more bitrate for complex scenes.
  • Frame rate. In Hikvision’s tables, dropping from 30 to 15 fps halves the recommended bitrate.
  • Smart codecs. Axis reports that Zipstream’s dynamic region of interest saves 10 to 50 percent, with similar ranges for dynamic GOP and dynamic frame rate.
  • Image quality profile. Hanwha’s High profile uses about double the bitrate of Medium.

Bandwidth Formulas

  • Per camera (Mbps) = recommended Kbps ÷ 1,000 × (1 + scene headroom)
  • Total (Mbps) = per-camera Mbps × number of cameras
  • Link share (%) = total Mbps ÷ link Mb/s × 100
  • Cameras per link = link Mb/s ÷ per-camera Mbps, rounded down
  • Data per day (GB) = Mbps × 86,400 ÷ 8 ÷ 1,000

Example: 16 cameras at 4 MP, H.265, 30 fps use 16 × 4.10 = 65.5 Mbps, about 66 percent of a 100 Mb/s link and 6.6 percent of a 1 Gb/s uplink.

Limits of This Chart

The chart is a planning starting point, not a measurement of your camera. It uses one manufacturer’s recommendations for the main stream only. Constant and variable bitrate modes, GOP length, sub-streams, and multiple viewers change real traffic, and Ethernet line rates from IEEE 802.3 are not the same as usable throughput.

Frequently Asked Questions

How much bandwidth does a 4MP camera use with H.265?

Hikvision recommends 4,096 Kbps (about 4.1 Mbps) for a 4 MP (2560 × 1440) camera on H.265 at 25 or 30 fps, 2,048 Kbps (about 2.0 Mbps) at 15 fps, and a 2,048 Kbps target at 30 fps with H.265+. Hikvision adds that complex scenes may need 20 to 30 percent more.

Does H.265 really use half the bandwidth of H.264?

ITU said in 2013 that HEVC (H.265) needs only half the bit rate of H.264, and Hikvision’s recommended tables halve every H.264 value for H.265. Axis is more cautious: it reports 15 to 40 percent lower bitrates at comparable quality, and its own street-scene tests show savings of about 18 to 29 percent.

How many IP cameras can a 100 Mbps or 1 Gbps link carry?

Divide the link speed by the per-camera bitrate. At Hikvision’s 4.1 Mbps for 4 MP H.265 at 30 fps, the raw math gives 24 cameras on 100 Mb/s and 244 on 1 Gb/s. Those are nominal line rates from IEEE 802.3, so leave room for protocol overhead, other traffic, and scene complexity.

Why does my camera use more bandwidth at night or in busy scenes?

Bitrate depends on what the camera sees. Hanwha lists lighting and scene activity as bitrate factors, and its highway scene profile uses twice the bandwidth of its retail profile. Axis measured 23.6 Mbps on H.264 for a busy city scene but 4.8 Mbps for its nighttime scene.

Is the bandwidth chart the same for every camera brand?

No. The chart uses Hikvision’s published recommendations because they are one of the few complete per-resolution tables a manufacturer publishes. Other brands, smart codecs, GOP length, and bitrate mode change the result, so use your camera’s own setting in the custom field when you know it.

Sources

Plan storage next

Once you know the bitrate, estimate how many days of recording your NVR can hold. Using a cloud plan instead? See how long security cameras keep footage by brand.

NVR Storage Calculator