UPS Runtime Calculator for Cameras, NVR, and PoE Switch
Add up the devices that must stay on during an outage, or type a total load. Then enter the UPS battery voltage, amp-hours, and number of batteries, or the battery energy in watt-hours.
Camera Power by PoE Class
A PoE camera can draw up to 4.0 W on Class 1, 7.0 W on Class 2, 15.4 W on Class 3, and 30 W on Class 4 (PoE+), measured at the switch port. Eight Class 3 cameras can therefore add up to 123 W to your UPS load.
| PoE class | Standard | Max power at switch port | 8 cameras | 16 cameras |
|---|---|---|---|---|
| Class 1 | 802.3af | 4.0 W | 32 W | 64 W |
| Class 2 | 802.3af | 7.0 W | 56 W | 112 W |
| Class 3 | 802.3af | 15.4 W | 123 W | 246 W |
| Class 4 | 802.3at (PoE+) | 30 W | 240 W | 480 W |
| Class 6 | 802.3bt | 60 W | 480 W | 960 W |
| Class 8 | 802.3bt | 90 W | 720 W | 1,440 W |
Class limits from the Ethernet Alliance overview of IEEE 802.3bt. Most cameras draw less than their class maximum, so the camera’s own datasheet value gives a closer estimate.
How to Size a UPS for a Camera System
- List every device that must stay on. Cameras alone are not enough. The NVR records, the PoE switch powers the cameras, and the router sends alerts.
- Find real wattages. CyberPower suggests the user manual or safety label, or volts × amps when only current is listed. Schneider Electric notes that nameplate ratings are often higher than actual draw.
- Add 25 percent headroom. CyberPower recommends that the load not exceed 80 percent of the UPS capacity, so multiply the total by 1.25.
- Check both watts and VA. Divide the minimum watts by the UPS power factor to get the minimum VA, as in Eaton’s formula.
- Confirm runtime on the chart. Use the UPS maker’s runtime chart or selector tool for the final choice.
Formula vs. Manufacturer Runtime
The simple formula assumes a battery delivers the same energy at any load. It does not. CyberPower’s CP1500PFCLCD (1500 VA / 1000 W, two 12 V / 9 Ah batteries, 216 Wh) shows how far apart the two can be at high loads.
| Load | Formula at 80% efficiency | CyberPower published runtime |
|---|---|---|
| Half load (500 W) | 20.7 min | 10 min |
| Full load (1000 W) | 10.4 min | 2.5 min |
Formula values are calculated by SecurityTechLab from the published battery size. Typical camera systems load a UPS far below half, where the gap is smaller, but always check your model’s chart.
UPS Runtime Formulas
- Total load (W) = cameras × watts per camera + NVR + PoE switch + other devices
- Battery energy (Wh) = battery volts × amp-hours × number of batteries
- Runtime (minutes) = battery Wh × efficiency ÷ load W × 60
- Minimum UPS watts = total load × 1.25
- Minimum UPS VA = minimum UPS watts ÷ power factor
- Battery needed (Wh) = load W × target minutes ÷ 60 ÷ efficiency
Example: 8 Class 2 cameras at 7.0 W, a 25 W NVR, 10 W for the switch, and a 10 W router add up to 101 W. Two 12 V, 9 Ah batteries hold 216 Wh, so at 80 percent efficiency the formula gives about 103 minutes. The minimum UPS is about 127 W and 181 VA at a 0.7 power factor.
Limits of This Calculator
This is a planning estimate, not a guarantee. Battery age, temperature, and discharge rate change real runtime, and efficiency varies with load, as Schneider Electric explains. Infrared lights, heaters, and PTZ motors can raise camera draw at night or in cold weather. Use the result to shortlist UPS models, then confirm with the manufacturer’s runtime data.
Frequently Asked Questions
How long will a UPS run my security cameras and NVR?
Divide the battery energy the UPS can deliver by your total load. A UPS with two 12 V, 9 Ah batteries stores 216 Wh, so a 150 W camera system at 80 percent efficiency would run about 69 minutes by the formula. Check the result against the manufacturer’s runtime chart, because batteries deliver less energy at high loads.
What size UPS do I need for a security camera system?
Add up the watts of the cameras, NVR, PoE switch, and router, then multiply by 1.25 so the load stays under 80 percent of the UPS watt rating, as CyberPower recommends. Divide that by the UPS power factor to get the minimum VA. For a 150 W load and a 0.7 power factor, that is at least 188 W and 268 VA.
Should I count PoE camera watts and the PoE switch separately?
Yes. PoE cameras take their power through the switch, so the switch draws its own consumption plus the power it delivers to every camera. Count each camera once at its PoE class or datasheet wattage, then add the switch’s own consumption from its datasheet.
Why is the real runtime shorter than the formula?
Battery discharge is not linear. CyberPower lists 10 minutes at half load and 2.5 minutes at full load for its CP1500PFCLCD, which has 216 Wh of battery. At 500 W the simple formula at 80 percent efficiency gives about 21 minutes, so treat the formula as an upper estimate at high loads.
What is the difference between VA and watts on a UPS?
Watts are the real power your devices use, and VA is the apparent power the UPS must handle. The ratio is the power factor. Eaton gives the formula VA = watts ÷ power factor, and CyberPower’s CP1500PFCLCD is rated 1500 VA and 1000 W, a power factor of about 0.67.
Sources
All sources accessed November 2, 2026.
- CyberPower, “Runtime Recommendations” (Power Blog). Used for: Load should not exceed 80% of UPS capacity; total load × 1.25 = minimum capacity; volts × amps = watts.
- CyberPower, CP1500PFCLCD product specifications. Used for: 1500 VA / 1000 W rating, 0.7 output power factor, two 12 V / 9 Ah batteries, 10 min at half load and 2.5 min at full load.
- CyberPower, “Watts vs. Volt-Amperes (VA)”. Used for: Power factor definition; output watt capacity 20–30% above the connected load.
- Eaton, “VA Versus Watts”. Used for: VA = watts ÷ power factor.
- Schneider Electric (APC), “UPS buying guide”. Used for: Watt capacity 20–30% above total load; runtime depends on battery capacity and load.
- Schneider Electric (APC), “APC UPS Selector”. Used for: Nameplate ratings are often higher than actual draw; typical router or switch draw of 10–30 W.
- Schneider Electric, “What is UPS efficiency and how is it calculated?” (FAQ000244215). Used for: Efficiency definition and its dependence on load.
- Ethernet Alliance, “Introducing IEEE 802.3bt” (Types and Classes). Used for: Maximum power per PoE class at the switch port, used as camera presets.
Plan the rest of your system
Check that your PoE switch can power every camera, then size the recorder’s storage. For the recorder itself, see what an NVR system is.
PoE Budget Calculator
